Pleasant Hearth 238-29-65 Use and Care Manual download pdf

PACKAGE CONTENTS

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-447-4768, 8:30 a.m. - 4:30 p.m., CST, Monday - Friday.

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

HARDWARE CONTENTS (shown actual size)

ASSEMBLY INSTRUCTIONS

1. Screw each of the four legs (Q) into the

predrilled holes in each corner of the base (C).

Screw middle leg (R) into predrilled hole in

center brace of base (C).

2. Insert two dowels (DD) into predrilled holes on

each end of shelf rail (F). Slip one end of shelf

rail (F) into predrilled holes in upper edge of

left inner panel (J) and the other end into

predrilled holes in upper edge of right inner

panel (K). Press together until both joints are

snug. Lay base (C) face up on a flat, level surface

and insert four dowels (DD) into predrilled

holes in center area of base (C). Slip panel

assembly over dowels (DD) so that the dowels

(DD) fit into predrilled holes in bottom edge of

assembly.

Insert two bolts (AA) through flat

washers (BB), lock washers (CC), predrilled

holes in edge blocks and into predrilled holes

base (C)

. Tighten with Phillips screwdriver

(not included).

Repeat on opposite side.

ITEM #0000000

MODEL #23-29-65

HERITAGE MEDIA MANTEL

FOR 23 IN. FIREBOX

Français p. 11

Español p. 21

PART DESCRIPTION QUANTITY

A Top Panel 1

B Top Shelf 1

C Base 1

D Adjustable Shelf 2

E Top Shelf Divider 1

F Shelf Rail 1

G Left Side Panel 1

H Right Side Panel 1

J Left Inner Panel 1

K Right Inner Panel 1

L Lower Back Panel 2

M Upper Back Panel 1

N Left Cabinet Door 1

P Right Cabinet Door 1

Q Leg 4

R Middle Leg 1

Bolt

Qty. 20

Flat

Washer

Qty. 20

Dowel

Qty. 28

SAFETY INFORMATION

PREPARATION

Please read and understand this entire manual before attempting to assemble, operate or install

the product.

WARNING

• Mantel is heavy and should be assembled near its desired location.

• It is recommended that two people move the finished mantel to prevent injury.

Before beginning assembly of product, make sure all parts are present. Compare parts with

package contents list and hardware contents list. If any part is missing or damaged, do not

attempt to assemble the product.

Estimated Assembly Time: 45 minutes

Tools Required for Assembly: Phillips screwdriver (not included).

ONE YEAR LIMITED WARRANTY

If within one year from the date of original purchase this item fails due to a defect in material or

workmanship, we will replace or repair at our option, free of charge. To order parts or to obtain warranty

service, call 1-877-447-4768, Monday – Friday, 8:30 a.m. – 4:30 p.m., CST. This warranty does not

cover defects resulting from improper or abnormal use, misuse, accident, or alteration. Failure to follow

all instructions in the owner’s manual will also void this warranty. The manufacturer will not be liable for

incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion of incidental or consequential damages may

not apply to you. This warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

Variations in actual wood color and finishes which may result from natural characteristics of the wood,

such as grain patterns, mineral streaks and the like, are not considered defects. As wood continues to

move and age you may notice these slight differences in color, even on different parts of any individual

unit. Sound knots and slight surface cracks are true personality of a quality piece of wood furniture.

CARE AND MAINTENANCE

• To maintain the finish, clean with a soft, slightly damp cloth and buff with a dry cloth.

• Wood furniture should never be dragged across a floor. The added stress from dragging the unit

may cause the dragged edge to splinter or it may cause a joint to loosen.

ASSEMBLY INSTRUCTIONS

3. Insert two dowels (DD) into predrilled holes

in each end of top shelf (B). Slip one end of

top shelf (B) into predrilled holes on inside

face of left side panel (G) and the other end

into predrilled holes on inside face of right side

panel (H). Press together until both joints are

snug.

Hardware Used

x 4

Bolt

Flat Washer

Hardware Used

x 4

Dowel

W armi ng Y our Hom e. Wa rming Y o ur H ear t.

Lock

Washer

Qty. 20

Lock Washer

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at at 1-877-447-4768, 8:30 a.m. - 4:30 p.m.,

CST, Monday - Friday.

PART DESCRIPTION PART #

A Top Panel 20-12-178

B Top Shelf 20-12-179

C Base 20-12-180

D Adjustable Shelf 20-12-181

E Top Shelf Divider 20-12-182

F Shelf Rail 20-12-183

G Left Side Panel 20-12-184

H Right Side Panel 20-12-185

J Left Inner Panel 20-12-186

K Right Inner Panel 20-12-187

L Lower Back Panel 20-12-188

M Upper Back Panel 20-12-189

N Left Cabinet Door 20-12-190

P Right Cabinet Door 20-12-191

Q Leg 20-12-192

R Middle Leg 20-12-193

AA Bolt 20-12-194

BB Flat Washer 20-12-195

CC Lock Washer 20-12-196

DD Dowel 20-12-197

EE Screw 20-12-198

FF Knob Screw 20-12-199

GG Cabinet Door Knob 20-12-200

HH Shelf Support 20-12-201

Printed in China

20-10-128

4. Insert four dowels (DD) into predrilled holes

in base (C). Insert four dowels (DD) into

predrilled holes in top edge of left and right

inner panels (J&K). Set top shelf assembly

over dowels (DD) in base (C) and inner panel

assembly so that the dowels (DD) fit into

predrilled holes in bottom edges of left and

right side panels (G&H) and underside of top

shelf (B). Press down until all joints are snug.

Hardware Used

ASSEMBLY INSTRUCTIONS

Insert two bolts (AA) through flat washers (BB),

lock washers (CC), predrilled holes in edge

blocks and into predrilled holes in

base (C)

Tighten with Phillips screwdriver (not included).

Repeat on opposite side.

Hardware Used

x 4

Bolt

Flat Washer

Lock Washer

x 4

6. Lay assembly on its back.

Insert four bolts (AA)

through flat washers (BB), lock washers (CC),

predrilled holes in edge blocks and into predrilled

holes on right side of assembly as illustrated.

Tighten with Phillips screwdriver (not included).

Repeat on opposite end.

Hardware Used

x 8

Bolt

Flat Washer

Lock Washer

Screw

Qty. 42

Knob

Screw

Qty. 2

Shelf

Support

Qty. 8

Cabinet

Door Knob

Qty. 2

x 8

Dowel

x 8

Dowel

ASSEMBLY INSTRUCTIONS

7. With assembly sitting upright, insert two

dowels (DD) into predrilled holes in top of

top shelf (B). Slip top shelf divider (E) over

dowels (DD) so that the dowels fit into

predrilled holes in bottom edge.

Press

down until snug.

Hardware Used

8. With assembly sitting upright, insert six

dowels (DD) into predrilled holes in top of

edges of assembly. Slip top panel (A) over

dowels (DD) so that the dowels fit into

predrilled holes in underneath side of top

panel (A).

Insert two bolts (AA) through flat

washers (BB), lock washers (CC), predrilled

holes in edge blocks,and into predrilled holes

top panel (A)

. Tighten with Phillips screwdriver

(not included).

Repeat on opposite side.

Hardware Used

ASSEMBLY INSTRUCTIONS

9. Attach upper back panel (M) and lower back

panels

(L) by inserting screws (EE) into

predrilled holes and tightening with Phillips

screwdriver (not included).

Hardware Used

11. Attach right cabinet door (P) to hinges on

assembly. Attach cabinet door knob (GG) with

knob

screw (FF) inserted through predrilled hole

in right cabinet door (P). Tighten with Phillips

screwdriver (not included).

Repeat with left cabinet door (N).

Hardware Used

x 2

Cabinet

Door Knob

Knob Screw

x 42

Screw

x 4

Bolt

Flat Washer

Lock Washer

x 4

x 2

Dowel

x 6

Dowel

ASSEMBLY INSTRUCTIONS

10. Insert shelf supports (HH) into predrilled

holes as illustrated, keeping all shelf supports

(HH) parallel to each other. Lay adjustable

shelves (D) in place on each side of assembly.

Hardware Used

x 8

Shelf Support

100%

BLACK

FONT & SOFTWARE USAGE STATEMENT

COLOR USAGE & PRINT REQUIREMENTS

ALL INSTRUCTION MANUALS AND RELATED MATERIAL CREATED THROUGH

ADAPTATION OF THESE TEMPLATES MUST BE APPROVED BY LOWE’S

BRAND PACKAGING DEPARTMENT PRIOR TO PRODUCTION.

CONTACT: BRAND PACKAGING DEPARTMENT, LOWE’S COMPANIES, INC.

ATTN: PACKAGING STANDARDS

1000 LOWE’S BOULEVARD, MAIL STOP: 4WTD

MOORESVILLE, NC 28117

704-758-2785

DO NOT USE ANY COLOR GRAPHICS OR PHOTOGRAPHY IN YOUR INSTRUCTION

MANUALS. INSTRUCTION MANUALS PRINT IN GREYSCALE ONLY.

ALL GRAPHICS SHOWN ARE FOR SIZE AND POSITION ONLY; FINAL LINE-ART GRAPHICS

ARE REQUIRED FOR RELEASE TO PRESS.

IMPORTANT VENDOR NOTE

VENDORS ARE RESPONSIBLE FOR THE EXECUTION AND ACCURACY OF THEIR

INSTRUCTION MANUALS. THEY ARE SOLELY RESPONSIBLE FOR INSERTING ALL OF THE

CORRECT LEGAL CERTIFICATION, WARNING, WARRANTY, AND OTHER APPLICABLE

PRODUCT INFORMATION. HARDWARE MUST BE SHOWN AS ACTUAL SIZE IN THE

HARDWARE CONTENTS SECTION WITH LINE ART DRAWING OF THE HARDWARE, THE

DIMENSIONS, NAME DESCRIPTOR AND QUANTITY. LOWE’S IS NOT RESPONSIBLE FOR

ANY INCURRED DESIGN, TRANSLATION OR PRINTING COSTS. PLEASE REFER TO THE

TRANSLATION REQUIREMENTS ON LOWESLINK.COM

• FONTS USED ON THIS FILE: SEE FONT LEGEND.

• CONTACT YOUR APPROPRIATE FONT VENDOR TO PURCHASE THE REQUIRED FONTS

FOR THIS PACKAGE LINE.

• ADOBE ILLUSTRATOR CS3 WAS USED TO CREATE THIS FILE.

LOWE’S REQUIRES EACH VENDOR TO OBTAIN THEIR OWN LINE-ART GRAPHICS. ALL INSTRUCTION MANUAL GRAPHICS WILL

BE APPROVED BY LOWE’S BRAND MANAGEMENT DURING PROOFING.

THIS DESIGN IS PROPRIETARY AND CONFIDENTIAL TO LOWE’S COMPANIES, INC. AND CANNOT BE COPIED OR OTHERWISE

REPRODUCED OR USED WITHOUT THE EXPRESS WRITTEN PERMISSION OF LOWE’S.

THESE ARE THE PANTONE COLORS THAT ARE USED IN THIS FILE.

THESE MUST BE USED WHEN CREATING ANY OTHER PACKAGING.

THE ADDITION OF OTHER SPOT COLORS IS NOT PERMITTED.

ARTWORK DISCLAIMERS

FONT LEGEND

ALL FONTS MUST BE ARIAL BOLD OR ARIAL REGULAR, 12 PT. (MINIMUM) ON 14 PT. LEADING UNLESS OTHERWISE SPECIFIED.

REQUIRED PAPER TYPE

USE THE FOLLOWING PAPER FOR YOUR INSTRUCTION MANUALS:

• PAPER BASIS WEIGHT: 20-lb. PAPER OR 75 GRAMS/SQ METER

• DOCUMENT SIZE: PRINTED TWO-SIDES ON TABLOID OR A3 AND FOLDS

TO LETTER SIZE OR A4. INCLUDE SAMPLE MOCK-UP TO INDICATE

FOLD(S) AND PAGE LAYOUT.

THIS COLOR IS USED FOR

NOTES AND DOES NOT

PRINT.

CALL OUTS

(DO NOT PRINT)

THIS COLOR INDICATES

ALL TEXT TO BE CHANGED

WITH PRODUCT SPECIFIC

TEXT.

EDITABLE TEXT

(DO NOT PRINT)

1 2 3 4 5 6 7 8 9 10

ARTWORK DISCLAIMERS 1
FONT LEGEND 1